Sustav za mjerenje kapaciteta LiFePO4 baterija

master's thesis

• Title (english): System for LiFePO4 battery capacity measurement
• Author: Tomislav Ivaniš
• Mentor: Mario Vražić (mentor)
• Committee member: Mario Vražić (predsjednik povjerenstva)
• Committee member: Jadranko Matuško (član povjerenstva)
• Committee member: Šandor Ileš (član povjerenstva)
• Granter: University of Zagreb; Faculty of Electrical Engineering and Computing; Zagreb
• Defense date and country: 2017-07-07, Croatia
• Scientific / art field, discipline and subdiscipline: TECHNICAL SCIENCES; Electrical Engineering

Abstract

U ovom diplomskom radu opisana je simulacija i projektiranje standardnih pasivnih, a zatim i aktivnih komponenti sinkronog silaznog učinskog pretvarača koji će puniti ili prazniti bateriju zadanom referentnom strujom. Odabrani su hladnjaci za sve tranzistorske komponente te je dan raspon vrijednosti potrebnog teretnog otpornika. Zatim je pretvarač s baterijom matematički modeliran u prostoru stanja, nakon čega je izvršeno usrednjivanje modela. Iz usrednjenog modela je dobivena prijenosna funkcija po struji baterije. Metodom postavljanja polova dobiveni su parametri regulatora te se zatim tako dobiveni regulator diskretizirao. Usporedno sa simulacijom projektiran je i elektronički podsustav za pojačavanje signala, optičko odvajanje sustava te mjerenje veličina potrebnih za upravljanje. Za sustav je izrađena električna shema, te je iz nje projektirana i izrađena tiskana pločica. Predviđene elektroničke komponente su zatim montirane i zalemljene. Za mikroračunalni ugradbeni sustav napisan je program za upravljanje sustavom. U mikroračunalo je najprije učitan program punilac te zatim i program za upravljanje sustavom punjenja i pražnjenja baterije. Sustav je na kraju uspješno testiran na promjenu reference struje, pri čemu su vremena prijelaznih pojava zadovoljavajuća za korištenje ili daljnja testiranja.

Abstract (english)

This graduate thesis describes the simulation and the design of the synchronous buck converter used for charging and discharging LiFePO4 batteries. The complete system is designed to charge or discharge any Li-ion battery with controllable load current. Active and passive components as well as the coolers were selected appropriately, as was the range of acceptable input resistive loads for battery drainage. The converter-battery system was mathematically modeled in state space, after which the model was averaged. From the averaged model, a transfer function was calculated regarding to the battery current. Using pole placement method the regulator parameters were obtained, followed by a z-transformation of the regulator itself. Simultaneously with the simulation, the electronic subsystem for signal amplification, optical separation and signal measurement was also designed. Appropriate electrical schematic was created, according to which the printed circuit board was designed. The PCB was routed and manufactured. Next, the electronic components were installed and soldered to the board. A system control firmware was written for the embedded microcontroller, which was firstly loaded with the bootloader, and secondly with the battery charger/discharger controller firmware. The system was successfully tested to the current reference change. The rise and fall times were satisfactory for usage or further testing.

• Keywords: Sinkroni silazni pretvarač; Baterija; Kapacitet; LiFePO4; PLECS; prostor stanja; upravljanje pretvaračem; KiCad; tiskana pločica; ugradbeni sustav; mikrokontroler; Arduino; Računalno upravljanje
• Keywords (english): Synchronous buck converter; Battery; Capacity; LiFePO4; PLECS; State-space; Power converter control; KiCad; Printed circuit board; Embedded system; Microcontroller; Arduino; Computer control
• Language: croatian
• URN:NBN: urn:nbn:hr:168:405447
• Study programme: Title: Electrical Engineering and Information Technology; Study programme type: university; Study level: graduate; Academic / professional title: magistar/magistra inženjer/inženjerka elektrotehnike i informacijske tehnologije (magistar/magistra inženjer/inženjerka elektrotehnike i informacijske tehnologije)
• Type of resource: Text
• File origin: Born digital
• Access conditions: Closed access
• Created on: 2019-03-13 20:59:35